Technology
|
|
IEEE 802.3 10Base-T IEEE 802.3u 100Base-TX IEEE 802.3u 100Base-FX IEEE 802.3x Flow Control and Back Pressure
|
|
|
Supports 4 types of forwarding mode, store and forward, modify cut-through, pure converter and converter mode with auto negotiation. This feature is selected by DIP-switch.
|
|
|
Supports Bi-directional Link Loss Forwarding function.
|
|
|
RJ-45 port supports auto-negotiation and forced mode – 10Mbps/Half Duplex.
|
|
|
64~1600Bytes @ Pure Converter mode.
|
|
|
Store and Forward: 250uS Modify Cut-Through: 17uS Converter : 1.6uS
|
|
IEEE 802.3 flow control /back-pressure
|
|
|
|
Supports port link down and power event alarm relay output, controlled by DIP switch.
|
|
|
Dry Relay Output with 1A @24V DC ability
|
|
Interface
|
|
Ethernet copper port: 1 10/100TX ports with Auto MDI/MDI-X, Auto Negotiation Fiber port: 1 100Mbps Fiber port, SC
|
|
|
RJ-45 Connector: 10Base-T: 2-pairs UTP/STP Cat-3,4 TIA/EIA 568-B cable, 100 meters 100Base-TX : 2/4 pairs UTP/STP Cat.5 TIA/EIA 568-B cable, 100 meters Fast Ethernet Fiber Transceiver: SC connector: supports multi-mode or single-mode optical fiber Multi-mode fiber: 50/125um or 62.5/125um, max. distance 2KM Single-mode fiber: 8/125um, 9/125um or 10/125 um, max distance 30KM
|
|
|
JetCon 2301-m: 2KM (Max.) Wave-length: 1310nm Min TX Power:-19dBm Max TX Power:-14dBm Min RX Sensitivity:-14dBm Max RX Sensitivity:-31dBm Link budget:12dBm JetCon 2301-s : 30KM (Max.) Wave-length:1310nm Max TX Power:-8dBm Min TX Power:-15dBm Max RX Sensitivity:-34dBm Min RX Sensitivity:-8dBm Link budget: 19dBm JetCon 2301-s (WDM-A): Single-mode: 30KM (Max.) Wave-length: TX 1310nm, RX 1550nm Min TX Power:-14dBm Max TX Power:-8dBm Min RX Sensitivity: 0 dBm Max RX Sensitivity:-31dBm Link budget:17dBm JetCon 2301-s (WDM- ): Single-mode: 30KM (Max.) Wave-length:TX 1550nm, RX 1310nm Max TX Power:-14dBm Min TX Power:-8dBm Max RX Sensitivity: 0 dBm Min RX Sensitivity:-31dBm Link budget: 17dBm
|
|
|
System Power (Green on) : Power 1 , 2 Relay Alarm: Active (Red) Link Loss Forwarding : Far end fault event occurred (Red on) Op. Mode: Convert (Green on) (Controlled by DIP Switch 4) Fiber Ethernet Port: Link/Activity (Green on/Blinking), Full Duplex/Collision (Yellow on/Yellow Blinking) Ethernet Port: Link/Activity (Green on/Blinking), Full Duplex/Collision (Yellow On/ Yellow Blinking)
|
|
|
DIP Switch 1: LLF Enable/Disable, default disable (DIP 1 off) DIP Switch 2: TX port Auto-Negotiation (OFF)/10H (ON), default disable (DIP 2 off) DIP Switch 3 & 4: Forwarding Mode Selection, default store & forward mode (DIP 3,4 off) DIP Switch 5: Power Alarm, default disable (DIP 5 off) DIP Switch 6: Port Alarm, default disable (DIP 6 off) DIP Switch 7: Flow Control, default enable (DIP 7 off)
|
|
|
|
|
|
Power Requirements
|
|
DC 10~60V with polarity reverses correction. Supports Positive/Negative power system
|
|
|
|
Mechanical
|
|
|
|
Ingress Protection code - 30
|
|
|
55 mm (W) x 120 mm (H) x 99mm (D)
|
|
|
|
Environmental
|
|
-25 ~ 75°C (JetCon 2301-w:-40 ~ 75°C)
|
|
|
5% ~ 95% (Non-condensing)
|
|
|
|
|
5% ~ 95% (Non-condensing)
|
|
|
AC 1.5KV on port to port and port to power
|
|
|
|
Regulatory Approvals
|
|
EN 61000-6-4, CISPR 16-1-2/-2-1/-2-3 CISPR 22
|
|
|
EN 61000-6-2, EN 61000-6-2 IEC 61000-4-2,IEC61000-4-3, IEC61000-4-4, IEC61000-4-5, IEC61000-4-6, IEC61000-4-8
|
|
|
|
|
|
|
|