Cerca
Filters
Close

JetNet-4706f

Switch PoE 6 porte con 4 porte PoE e 2 porte in fibra ottica (managed)
Caratteristiche
  1. 4x 10/100 TX PoE ports and two redundant 100 FX uplink ports
  2. Two Fiber links for long distance transmission
  3. Supports Multi-mode 2KM, Single-mode 30KM
  4. DC 48V Power Input for IEEE 802.3af 48V PoE output
  5. Up to 25W per port by Forced powering mode
  6. Up to 80W for total power budget
  7. IEEE 802.3af for PoE detection and classification resistors
  8. PoE control and schedule by hour/weekly basis
  9. Auto-detect Powered Device status for device auto-reset (LPLD)
  10. Multiple Super Ring technology (MSRTM) (5ms recovery time)
  11. Rapid Dual Homing (RDHTM) technology
  12. SNMP v1/v2c/v3, IGMP snooping v1/v2/v3, RMON, VLAN, QoS
  13. Network security by IP/MAC address, SSL and SSH
  14. Built-in hardware watchdog timer for system auto-reset
  15. -40°~60°C wide operating temperature
Produttore:: Korenix Technology

Technology
Standard
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-T
IEEE 802.1p Class of Service
IEEE 802.3af Power Over Ethernet(PoE)
IEEE 802.3at High Power PoE
IEEE 802.1D Spanning Tree
IEEE 802.1w Rapid Spanning Tree

Performance
Switch Technology
Store and Forward Technology with 3.2Gbps wire-speed
non-blocking Switch Fabric
System Throughput
1.785Mpps
MAC Address
2000
Packet Buffer
Embedded 1Mbits shared buffer
Transfer performance
14,880pps for Ethernet and 148,800 for Fast Ethernet and transfer packet size from 64 to 1522Bytes
PoE Technology
End-Span wiring architecture
PD classification detection, class ID 0~3 follow IEEE802.3af standard, and 25W High power deliver procedures for class ID 4.
Pin assignment: V+ (RJ-45 Pin 4,5), V- (RJ-45 Pin 7,8), TX (RJ-45 Pin 1,2), RX (RJ-45 Pin 3,6)
Protection: Provides over-current protection by PD class ID

Management
Management interface
SNMP v1, v2c and v3, Web browser, Korenix View, Korenix NMS, and CLI Management
Management Security
4 entries for web, telnet, SNMP management security
SNMP Trap
Provides Cold start, Warm start, Port event, Power event, Authentication failure, PoE trap and Korenix private trap for proprietary functions
SNMP MIB
RFC 1213 MIBII, RFC 1493 Bridge MIB, RFC 1757 RMON MIB, RFC 2674 VLAN MIB, RFC 1643 Ethernet like MIB, RFC1215 Trap MIB, RFC 3621 Power Ethernet MIB, Korenix Private MIB
Korenix Utility
Supports Korenix View and Korenix NMS with IEEE 802.1AB Link Layer Discovery Protocol for device and link auto-topology discovery
Firmware upgrade
TFTP, HTTP and Korenix View
System Log
1000 system entries for system or remote log server
Event Alarm Relay
1A @24V Dry Relay Contact output for port link down, PoE and System power events.
Quality of Service
Quality of Service determined by port, Tag and IPv4 Type of Service
Class of Service
IEEE802.1p class of service, with 4 priority queues
DHCP
Supports DHCP Cilent and DHCP Server function with specified IP exclusion and MAC binding function
Timer
Supports Network Time Protocol (NTP) to synchronize time from NTP Server
VLAN
Port based VLAN
IGMP Snooping
Supports IGMP Snooping v1/v2/v3 and IGMP Query v1/v2
Network Redundancy
Supports Multiple Super Ring function for network redundancy with 5ms network recovery time; To inter-operate with other higher-level switches, JetNet 4706f provids RapidDual Homing II technology to conform with RSTP protocol. JetNet 4706f also conforms with IEEE802.1D 2004 edition for RSTP and STP standard protocols
PoE Port Control
Supports user configuration for PoE enable disable, or based on schedule
Power Limit Control
The control mode supports IEEE802.3af standard, Manual and Ultra mode for 25W Hi-power or forced powering mode for Non-standard PD. The maximum DC power delivery on each PoE port is 12.9W@DC 48V input or 25W @ DC57V input
PoE Scheduling Control
Each PoE port can be activated and powered scheduling with different rule. It supports weekly scheduling by hourly basis.
LPLD function
The Link Partner Line Detect function (LPLD) is available on PoE ports. With the LPLD function, the PoE port can keep attached PD alive.
IP Security
IP security to prevent unauthorized access

Interface
Number of Ports
4 x 10/100Base-TX with PoE Injector
2 x 100Base-FX ports
1 x RS-232 Console
Connectors
10/100TX: RJ-45
100Base-FX: SC
Console: RJ-45
Power & Relay Alarm: 6-pin Terminal Block
Power Consumption
8 Watts @ 50V (Maximum) without PD loading
Cable
10Base-T: 4-pair UTP/STP Cat. 3, 4, 5 cable, EIA/TIA 568B 100-ohm(100m)
100Base-TX: 4-pair UTP/STP Cat. 5 cable, EIA/TIA 568B 100-ohm(100m)
100Base-FX: Multi-mode 50~62.5/125um; Single-mode 8~10/125um
Fiber Transceiver
JetNet4706f-m, Multi-mode: 2KM max. distance
Wave-length: 1310nm
Min Tx Power:-19dBm
Max Tx Power:-14dBm
Min Rx Sensitivity:-30dBm
Link budget:11dBm
JetNet 4706f-s, Single-mode: 30KM max. distance
Wave-length:1310nm
Max Tx Power:-8dBm
Min Tx Power:-15dBm
Min Rx Sensitivity:-34dBm
Link budget:19dBm
Rest Button
For system reboot and factory default setting
Diagnostic LED
Power LED: Power 1/Power 2 (Green)
Fast Ethernet Port 1~4: Link(Green)/Activity (Green blinking),
PoE Powering (Yellow on), PoE Detect (Yellow blinking),
PoE Disable (Yellow off), PoE Powering failure (Yellow fast blinking)
Fast Ethernet Port 5,6: Link(Green)/Activity (Green blinking)
Alarm (Red): Port link down or power failure occurred

Power Requirements
System Power
Support positive or negative power system with DC 48~57V power input range and polarity reverse protection
Power Consumption
8 Watts @ 50V (Maximum) without PD loading

Mechanical
Installation
DIN-Rail mount or desktop or wall mount
Case
IP-31 grade aluminum metal case
Dimensions
46.5 mm (H) x 174.8 mm (W) x 136 mm (D) without DIN-rail mount
Weight
0.72 kg with package
0.65 kg without package

Environmental
Operating Temperature
-40°C~60°C
Operating Humidity
0% to 95% (Non-condensing)
Storage Temperature
-40 to 80°C
Storage Humidity
5% to 95% (Non-condensing)

Regulatory Approvals
EMI
FCC Class A; CE/EN55022:2003 Class A
CE/EN61000-3-2:2001 Harmonic Test
CE/EN61000-3-3:1995 Flicker test
EMS
EN61000-4-2:1998, ESD
EN61000-4-3:1998, RS
EN61000-4-4:1995, EFT
EN61000-4-5:1995
EN61000-4-6:1996
EN 50155 Railway
compliance
Safety
UL/cUL60950-1, CSA C22.2 No.60950-1-03
Shock
IEC 60068-2-27
Free Fall
IEC 60068-2-32
Vibration
IEC 60068-2-6
MTBF
272,306 Hours, MIL-HDBK-217F GB standard
Warranty
5 years

Technology
Standard
IEEE 802.3 10Base-T
IEEE 802.3u 100Base-T
IEEE 802.1p Class of Service
IEEE 802.3af Power Over Ethernet(PoE)
IEEE 802.3at High Power PoE
IEEE 802.1D Spanning Tree
IEEE 802.1w Rapid Spanning Tree

Performance
Switch Technology
Store and Forward Technology with 3.2Gbps wire-speed
non-blocking Switch Fabric
System Throughput
1.785Mpps
MAC Address
2000
Packet Buffer
Embedded 1Mbits shared buffer
Transfer performance
14,880pps for Ethernet and 148,800 for Fast Ethernet and transfer packet size from 64 to 1522Bytes
PoE Technology
End-Span wiring architecture
PD classification detection, class ID 0~3 follow IEEE802.3af standard, and 25W High power deliver procedures for class ID 4.
Pin assignment: V+ (RJ-45 Pin 4,5), V- (RJ-45 Pin 7,8), TX (RJ-45 Pin 1,2), RX (RJ-45 Pin 3,6)
Protection: Provides over-current protection by PD class ID

Management
Management interface
SNMP v1, v2c and v3, Web browser, Korenix View, Korenix NMS, and CLI Management
Management Security
4 entries for web, telnet, SNMP management security
SNMP Trap
Provides Cold start, Warm start, Port event, Power event, Authentication failure, PoE trap and Korenix private trap for proprietary functions
SNMP MIB
RFC 1213 MIBII, RFC 1493 Bridge MIB, RFC 1757 RMON MIB, RFC 2674 VLAN MIB, RFC 1643 Ethernet like MIB, RFC1215 Trap MIB, RFC 3621 Power Ethernet MIB, Korenix Private MIB
Korenix Utility
Supports Korenix View and Korenix NMS with IEEE 802.1AB Link Layer Discovery Protocol for device and link auto-topology discovery
Firmware upgrade
TFTP, HTTP and Korenix View
System Log
1000 system entries for system or remote log server
Event Alarm Relay
1A @24V Dry Relay Contact output for port link down, PoE and System power events.
Quality of Service
Quality of Service determined by port, Tag and IPv4 Type of Service
Class of Service
IEEE802.1p class of service, with 4 priority queues
DHCP
Supports DHCP Cilent and DHCP Server function with specified IP exclusion and MAC binding function
Timer
Supports Network Time Protocol (NTP) to synchronize time from NTP Server
VLAN
Port based VLAN
IGMP Snooping
Supports IGMP Snooping v1/v2/v3 and IGMP Query v1/v2
Network Redundancy
Supports Multiple Super Ring function for network redundancy with 5ms network recovery time; To inter-operate with other higher-level switches, JetNet 4706f provids RapidDual Homing II technology to conform with RSTP protocol. JetNet 4706f also conforms with IEEE802.1D 2004 edition for RSTP and STP standard protocols
PoE Port Control
Supports user configuration for PoE enable disable, or based on schedule
Power Limit Control
The control mode supports IEEE802.3af standard, Manual and Ultra mode for 25W Hi-power or forced powering mode for Non-standard PD. The maximum DC power delivery on each PoE port is 12.9W@DC 48V input or 25W @ DC57V input
PoE Scheduling Control
Each PoE port can be activated and powered scheduling with different rule. It supports weekly scheduling by hourly basis.
LPLD function
The Link Partner Line Detect function (LPLD) is available on PoE ports. With the LPLD function, the PoE port can keep attached PD alive.
IP Security
IP security to prevent unauthorized access

Interface
Number of Ports
4 x 10/100Base-TX with PoE Injector
2 x 100Base-FX ports
1 x RS-232 Console
Connectors
10/100TX: RJ-45
100Base-FX: SC
Console: RJ-45
Power & Relay Alarm: 6-pin Terminal Block
Power Consumption
8 Watts @ 50V (Maximum) without PD loading
Cable
10Base-T: 4-pair UTP/STP Cat. 3, 4, 5 cable, EIA/TIA 568B 100-ohm(100m)
100Base-TX: 4-pair UTP/STP Cat. 5 cable, EIA/TIA 568B 100-ohm(100m)
100Base-FX: Multi-mode 50~62.5/125um; Single-mode 8~10/125um
Fiber Transceiver
JetNet4706f-m, Multi-mode: 2KM max. distance
Wave-length: 1310nm
Min Tx Power:-19dBm
Max Tx Power:-14dBm
Min Rx Sensitivity:-30dBm
Link budget:11dBm
JetNet 4706f-s, Single-mode: 30KM max. distance
Wave-length:1310nm
Max Tx Power:-8dBm
Min Tx Power:-15dBm
Min Rx Sensitivity:-34dBm
Link budget:19dBm
Rest Button
For system reboot and factory default setting
Diagnostic LED
Power LED: Power 1/Power 2 (Green)
Fast Ethernet Port 1~4: Link(Green)/Activity (Green blinking),
PoE Powering (Yellow on), PoE Detect (Yellow blinking),
PoE Disable (Yellow off), PoE Powering failure (Yellow fast blinking)
Fast Ethernet Port 5,6: Link(Green)/Activity (Green blinking)
Alarm (Red): Port link down or power failure occurred

Power Requirements
System Power
Support positive or negative power system with DC 48~57V power input range and polarity reverse protection
Power Consumption
8 Watts @ 50V (Maximum) without PD loading

Mechanical
Installation
DIN-Rail mount or desktop or wall mount
Case
IP-31 grade aluminum metal case
Dimensions
46.5 mm (H) x 174.8 mm (W) x 136 mm (D) without DIN-rail mount
Weight
0.72 kg with package
0.65 kg without package

Environmental
Operating Temperature
-40°C~60°C
Operating Humidity
0% to 95% (Non-condensing)
Storage Temperature
-40 to 80°C
Storage Humidity
5% to 95% (Non-condensing)

Regulatory Approvals
EMI
FCC Class A; CE/EN55022:2003 Class A
CE/EN61000-3-2:2001 Harmonic Test
CE/EN61000-3-3:1995 Flicker test
EMS
EN61000-4-2:1998, ESD
EN61000-4-3:1998, RS
EN61000-4-4:1995, EFT
EN61000-4-5:1995
EN61000-4-6:1996
EN 50155 Railway
compliance
Safety
UL/cUL60950-1, CSA C22.2 No.60950-1-03
Shock
IEC 60068-2-27
Free Fall
IEC 60068-2-32
Vibration
IEC 60068-2-6
MTBF
272,306 Hours, MIL-HDBK-217F GB standard
Warranty
5 years